Skip to content

Release Notes ​

Firmware is installed from the logged-in browser flasher at https://web.jkbmsr.com/flash. The current version per target is resolved from the authenticated API, not a static public file.

2026-11-11 · v0.9.18 ​

  • All three setup routes now run at the same time: the app over Bluetooth, USB (Improv) and the setup network. Before this, the Bluetooth window came first, so someone setting up from a laptop waited up to ten minutes before the setup network appeared.
  • A gateway that is already configured never enters setup on its own, even if its Wi-Fi fails. Only a device with no Wi-Fi stored, or a person holding BOOT, opens setup. That keeps a running gateway's Bluetooth link to the battery undisturbed.

2026-11-11 · v0.9.17 ​

  • A configured gateway whose Wi-Fi fails goes straight back to the setup network, with no Bluetooth window, so recovery is as fast as it was before.
  • The setup code is printed before the serial log is quietened for Improv, so it always reaches the console.

2026-11-11 · v0.9.16 ​

  • New: set the gateway up from the JK BMS Remote app. It advertises JKBMSR-Setup-XXXX while it has no Wi-Fi, and the app sends the network, the time zone and the account link in one go.
  • The six digit code printed in the console is required. It is never sent back over Bluetooth, so a gateway cannot be claimed by someone who is merely nearby.
  • The code is kept while the gateway is unprovisioned, so moving it from USB power to the battery does not invalidate it.

2026-11-11 · v0.9.15 ​

  • Fixed: a gateway on the 5 minute trial interval could miss its upload window and report far less often than the free tier. Uploads now fire on the interval they belong to instead of on one exact second.

2026-11-11 · v0.9.14 ​

  • The gateway now reports once, immediately, after it connects to the BMS, instead of waiting for the next interval boundary. On the free tier that boundary is an hour away, so a freshly booted gateway used to be invisible on the dashboard for up to an hour even though it was working.
  • The regular hourly (or faster, with Cloud Service) cadence is unchanged. One extra report per connection, throttled so a failed upload cannot retry in a tight loop.

2026-11-11 · v0.9.13 ​

  • New target: esp32-s3-16mb-quad for 16 MB ESP32-S3 modules with quad PSRAM. Until now the only 16 MB image was built for octal PSRAM, and a quad module running it resets in the bootloader before printing anything. If your board showed no log output at all after flashing, this is the image for it.
  • No change to the other seven targets beyond the version.

2026-11-10 · v0.9.12 ​

  • Faster recovery when the pack link drops. The reconnect delay now caps at 60 seconds instead of five minutes, and it resets as soon as a valid frame arrives, so a flaky link no longer escalates to the slowest retry and stays there.
  • A link that is connected but sends nothing for 30 seconds is now dropped and re-established, instead of holding a half-open session while the gateway reports "BMS link down". The stale-stream request still runs first.
  • If your dashboard showed long gaps while the gateway stayed online, this is the firmware for it.

2026-11-10 · v0.9.11 ​

  • The serial log now carries a timestamp on every line, rendered in the gateway's own time zone ([info] 2026-11-10 15:04:05 …). Before the first clock sync the lines show seconds since boot ([+12s]) rather than a made-up date.
  • Set the zone in the web app under Settings → General → Gateway time zone. It applies on the next check-in, with no reboot, and only changes how times are displayed: stored telemetry is always UTC.

2026-11-09 · v0.9.10 ​

  • Frame reassembly now works over the byte stream rather than per notification, so gateways whose frames are preceded by an echoed read command or AT commands no longer discard every frame as a header/checksum mismatch.
  • Fixes telemetry that stopped after a successful connection on some hardware.

2026-10-15 · v0.9.9 ​

  • Retries that make the pack beep are now backed off: the stalled-stream request and the reconnect attempt widen their delay instead of repeating on a fixed cadence, so a dead link stops beeping every few seconds.

2026-10-14 · v0.9.8 ​

  • JK-BMS only: the other vendor decoders are no longer part of the firmware build.
  • Cell presence is reported explicitly, so an unpopulated cell slot is no longer shown as a cell reading 0 V.

2026-10-13 · v0.9.7 ​

  • Production release across all supported gateway hardware.
  • Current version per releases/ota/*-latest.json.

2026-10-13 · v0.9.6 ​

  • Production release across all supported gateway hardware.

2026-10-13 · v0.9.5 ​

  • N16R8 target on arduino-esp32 3.2.0 / IDF 5.4.1.

2026-10-13 · v0.9.4 ​

  • N16R8 Octal-PSRAM target.

2026-10-13 · v0.9.3 ​

  • BLE-only BMS link.

2026-10-09 · v0.9.2 ​

  • Release script isolates the pioarduino (C6) core dir and bootstraps pip.

No tagged firmware releases exist between v0.1.2 (2026-07-05) and v0.9.2 in this repository.

For release-by-release details, see the release index at https://cdn.jkbmsr.com/ and the GitHub releases on https://github.com/janasco/jkbmsr/releases.