Supported Hardware
JK BMS Remote version 1 supports JK-BMS monitoring only.
Gateway firmware targets
The flasher offers one image per gateway target. The target decides the bootloader, the partition table and the PSRAM mode, so it has to match the board in your hand. The version number is the same for all of them: the version identifies the source, the target identifies the build.
| Target | Chip | Flash | PSRAM | Status |
|---|---|---|---|---|
esp32-classic-4mb | ESP32 | 4 MB | none | supported |
esp32-classic-8mb | ESP32 | 8 MB | none | experimental |
esp32-c3-4mb | ESP32-C3 | 4 MB | none | experimental |
esp32-c6-4mb | ESP32-C6 | 4 MB | none | experimental |
esp32-s3-4mb | ESP32-S3 | 4 MB | Quad | experimental |
esp32-s3-16mb | ESP32-S3 | 16 MB | Octal | supported |
esp32-s3-16mb-quad | ESP32-S3 | 16 MB | Quad | experimental |
ESP32-S3: which image?
PSRAM mode is a compile-time setting, not something the firmware can detect at runtime, so this is the one choice you cannot get wrong and fix later.
- The common N16R8 module has octal PSRAM: use
esp32-s3-16mb. - A 16 MB module with quad PSRAM has no correct image in the older target, so use
esp32-s3-16mb-quad. It uses the whole 16 MB either way. - Not sure, or the board is a clone? The symptom tells you. An octal image on a quad module resets in the bootloader before it can print anything: you see the ROM banner, the segment loads, then
rst:0x3 (RTC_SW_SYS_RESET)in a loop with no[info]lines at all. If you see the firmware's own log lines, the PSRAM mode is right and the target is right.
JK-BMS model matrix
Every model below is a JK-BMS product in the same JK protocol family. The Status column is marked honestly: a model is only marked hardware-tested or protocol-verified where that evidence actually exists:
hardware-tested: verified against live hardware.protocol-verified: a protocol capture exists for the model family.listed: same JK family, not individually tested.
PB Series
| Model | Status |
|---|---|
JK-PB1A16S10P | listed |
JK-PB1A16S15P | listed |
JK-PB2A16S10P | listed |
JK-PB2A16S15P | listed |
JK-PB2A16S20P | listed |
JK-PB2A16S30P | listed |
B Series
| Model | Status |
|---|---|
JK-B1A8S10P | hardware-tested |
JK-B1A8S20P | listed |
JK-B1A16S15P | listed |
JK-B1A20S15P | listed |
JK-B1A24S15P | listed |
JK-B2A8S20P | listed |
JK-B2A20S20P | listed |
JK-B2A24S15P | protocol-verified[^b2a24s] |
JK-B2A24S20P | protocol-verified[^b2a24s] |
[^b2a24s]: The capture on file covers the JK-B2A24S family; the two charge-current variants are not individually captured.
BD Series
| Model | Status |
|---|---|
JK-BD4A8S4P | listed |
JK-BD4A8S6P | listed |
JK-BD4A17S4P | listed |
JK-BD4A24S4P | listed |
JK-BD6A20S6P | listed |
JK-BD6A20S10P | listed |
JK-BD6A20S15P | listed |
JK-BD6A20S12P | listed |
JK-BD6A24S4PD | listed |
JK-BD6A24S6P | listed |
JK-BD6A24S6PD | listed |
JK-BD6A24S8P | listed |
JK-BD6A24S8PD | listed |
JK-BD6A24S10P | listed |
JK-BD6A24S12P | listed |
JK-BD6A24S12PD | listed |
JK-BD6A24S15P | listed |
JK-BD6A24S15PD | listed |
JK-BD6A24S20P | listed |
Active Balancer
| Model | Status |
|---|---|
JK-B4A24S | listed |
JK-B2A16S | listed |
JK-B15A24S | listed |
QB Series
| Model | Status |
|---|---|
JK-QB2A8S20P | listed |
Current product focus
- JK-BMS over Bluetooth (BLE)
- ESP32-family gateway
- JKBMSR Cloud backend
Not supported in version 1
- any BMS other than JK-BMS
- non-ESP32 firmware targets